McIntosh MAC1700 Stereo Receiver Wood Case Restored 1-Year Warranty

$2,299

-

  • Classic McIntosh Stereo Receiver combining amplification and radio reception in one component
  • 40 Watts per Channel rated output into 4- or 8-ohm loads
  • Tube FM Tuner paired with a solid-state preamplifier and power amplifier
  • FM Stereo Reception in a classic integrated receiver design
  • Vintage McIntosh Styling with the distinctive front-panel design and tuning display
  • Inspected and serviced by HQaudios
  • Backed by our 1-Year HQaudios Warranty

1 in stock

SKU: 15QJKE4057-VS24 Categories: , ,

McIntosh MAC1700 FM Stereo Receiver
Professionally Restored by HQaudios – Inspected & Tested – Backed by Our 1-Year Warranty

KEY HIGHLIGHTS
Classic McIntosh FM stereo receiver with integrated preamplifier and power amplifier
40 W RMS per channel into 4 or 8 ohms, both channels driven
Distinctive black upper panel and silver lower control panel on this unit
Output stage, power supply, and FM tuner serviced by HQaudios
Includes an HQaudios handcrafted wood case

PRODUCT OVERVIEW
Produced from 1967 to 1973, the McIntosh MAC1700 combines solid-state preamplifier and power amplifier stages with an FM stereo tuner. Its analog controls and selection of phono, tape, and auxiliary sources make it a versatile centerpiece for a classic two-channel audio system.

HQAUDIOS RESTORATION & TESTING
Professionally inspected, tested, and serviced. Aging or degraded components have been replaced where necessary to restore performance as close as possible to original factory specifications.
Before Restoration
During our initial inspection, the left channel produced weak, distorted sound. We identified a faulty output stage with a missing output transistor and a power-supply fault. FM reception was also not operating.
During Restoration
Capacitors: We tested and measured all capacitors; out-of-spec units were replaced with quality, correct-value parts.
Output Stage: We repaired the affected amplifier circuitry and installed two Sanken C1115 output transistors (×2).
Power Supply: We repaired the power-supply circuitry and replaced ten 1N5408 rectifier diodes (×10).
Power Amplifier Board: We inspected and serviced the power amplifier section.
Circuit Boards: We cleaned and inspected circuit boards and reinforced weak solder joints.
Bias & DC Offset: We measured and adjusted bias and DC offset to McIntosh factory specifications.
Lighting: We replaced dial and indicator lamps with new lighting components.
Switches & Controls: We cleaned and serviced switches and controls for smooth, stable operation.
Input/Output Jacks: We inspected and cleaned signal input and output connections.
FM Tuner Section: We serviced the FM section and restored reception.
Phono Stage: We tested both phono input paths for proper gain and channel balance.
Wood Case: We fitted a wood case handcrafted by HQaudios.
Cleaning & Detailing: We cleaned and detailed the chassis, front panel, knobs, and exterior surfaces.

After Restoration / Final Testing
Burn-in: A 72-hour burn-in test was completed to verify operating stability.
Stereo Operation: We tested the left and right channels for consistent output and evaluated the receiver during music playback.
Functions: We tested FM reception, source selection, available inputs and outputs, tone and balance controls, and speaker operation.

CONDITION
Technical Condition
Amplifier: Both channels produced audio during the final functional check.
FM Tuner: FM reception and tuning operation confirmed.
Controls: Input selection, volume, balance, and tone controls operated during testing.
Connections: Audio inputs and speaker connections were functionally checked.
Cosmetic Condition
Front Panel: Black upper tuning panel with a silver lower control section.
Wood Case: Light wood finish with a ventilated top, as shown in the photographs.
Visible Wear: Age-related wear is visible on some rear-panel metal surfaces and connections. Please review the actual-unit photographs for details.

Stereo Output and Final Listening Test Completed

SPECIFICATIONS
Brand: McIntosh
Model: MAC1700
Type: FM Stereo Receiver
Power Output: 40 W RMS continuous per channel into 4 or 8 ohms, both channels driven
Total Harmonic Distortion: Less than 0.25% at rated power, 30 Hz – 20 kHz
Frequency Response: 20 Hz – 20 kHz, ±0.5 dB at rated output
Damping Factor: Greater than 100
Phono Inputs: Phono 1 and Phono 2, 2.4 mV / 47 kilohms (MM)
Audio Inputs: AUX, Tape, Tape Monitor, Phono 1, Phono 2, Tape Head
Outputs: Left/right speaker terminals, tape output, headphone jack
Tuner Band: FM stereo
Factory Power Requirements: 117 V AC, 50/60 Hz
Dimensions: Front panel 16.0 W × 5.5 H in; chassis 15.0 W × 5.1 H × 14.5 D in
Net Weight: 34.0 lbs (receiver, excluding separate wood case)

WHAT IS INCLUDED
1 × McIntosh MAC1700 FM Stereo Receiver
1 × Wood case handcrafted by HQaudios
Only the items specifically listed above are included. Speakers, audio cables, and other demonstration accessories are not included.

SHIPPING & PACKAGING
Your vintage audio equipment will be professionally packed by HQaudios using protective materials appropriate for its size, weight, and construction. Large or heavy items may be palletized and shipped by freight when required for safer transportation.

HQaudios Professional Shipping and Packaging

Please contact us before purchase for the most current availability information.
1-YEAR WARRANTY & CUSTOMER SUPPORT
Your purchase is backed by our 1-Year HQaudios Warranty. Our team provides support before and after your purchase. If you have questions about setup, operation, compatibility, or your order, please contact HQaudios for assistance.

MORE FROM HQAUDIOS
Need restoration, repair, a custom faceplate or wood case, speaker stands, or a trade-in option? Contact HQaudios for available services and package pricing.

HQaudios Vintage Audio Repair and Restoration

HQaudios Custom Audio Projects

Reviews

There are no reviews yet.

Be the first to review “McIntosh MAC1700 Stereo Receiver Wood Case Restored 1-Year Warranty”

Recently viewed

You have not viewed any products yet.